//Generated by auto config tool v1.2
/**
 * For directions on how to use this firmware visit http://uf2.th3dstudio.com and click on your printer/board link
 * NO IMPLIED SUPPORT OR WARRANTY IS PROVIDED WITH THIS FIRMWARE AND IS PROVIDED AS-IS
 */
#pragma once
#define CONFIGURATION_H_VERSION 02010204

#define UNIFIED_VERSION "TH3D UFW 2.98"
#define STRING_DISTRIBUTION_DATE "2025-12-11"

#define ENDER3
#define ENDER3_STOCK_FRAME
#define EZABL
#define CUSTOM_PROBE
#define EZABL_FASTPROBE
#define EZABL_SUPERFASTPROBE
#define EZABL_PROBE_EDGE 20
#define EZABL_POINTS 5
#define KNOWN_HOTEND_THERMISTOR
#define KNOWN_HOTEND_THERMISTOR_VALUE 1
#define HIGH_TEMP_THERMISTOR
#define HIGH_TEMP_THERMISTOR_TEMP 300
#define STOCK_BED_THERMISTOR
#define ENABLE_PIDBED
#define DIRECT_DRIVE_PRINTER
#define CUSTOM_ESTEPS
#define CUSTOM_ESTEPS_VALUE 425
#define HOME_ADJUST
#define X_HOME_LOCATION -6
#define Y_HOME_LOCATION -10
#define POWER_LOSS_RECOVERY
#define LCD_LANGUAGE en
#define NOZZLE_TO_PROBE_OFFSET {0,-30,0}

/**
 * ****************************DO NOT TOUCH ANYTHING BELOW THIS COMMENT**************************
 * Core machine settings are below. Do NOT modify these unless you understand what you are doing.
 */

//BLTouch/CRTouch ABL Updates
#if ENABLED(BLTOUCH) && DISABLED(CUSTOM_PROBE)
  #define CUSTOM_PROBE
#endif

//Set Ender 3 Pro Machine Setting
#if ENABLED(ENDER3_PRO)
  #define ENDER3
#endif

//Set Ender 5 Pro Machine Setting
#if ENABLED(ENDER5_PRO)
  #define ENDER5
#endif

//Set ZSteps for ENDER5_NEW_LEADSCREW
#if ANY(ENDER5_NEW_LEADSCREW, ENDER5_PLUS)
  #define CREALITY_Z_STEPS 800
#else
  #define CREALITY_Z_STEPS 400
#endif

/**
 * Machine Configuration Settings
 */
 
//EZBoard based Machine Settings
#if ANY(CR10, CR10_MINI, CR10_S4, CR10_S5, CR10S, CR10S_MINI, CR10S_S4, CR10S_S5, ENDER2, ENDER2_PRO, ENDER3, ENDER5, ENDER5_PLUS, SOVOL_SV01, SOVOL_SV03, CR20, ENDER3_MAX)

  #define SERIAL_PORT -1
  #define SERIAL_PORT_2 0
  #define BAUDRATE 115200
  
  #if ENABLED(CR20) || ENABLED(ENDER2)
    #define MKS_MINI_12864
  #else
    #define CR10_STOCKDISPLAY
  #endif
  
  #if ENABLED(REVERSE_KNOB_DIRECTION) && DISABLED(ENDER5_PLUS)
    #define REVERSE_ENCODER_DIRECTION
  #endif
  
  #if ENABLED(CR10S) || ENABLED(CR10S_S4) || ENABLED(CR10S_S5) || ENABLED(SOVOL_SV01) || ENABLED(SOVOL_SV03) || ENABLED(ENDER3_MAX)
    //S models + SV01 assume that you have 2x motors, filament sensor, and are using the dual adapter.
    //So lets up the VREF on Z and reverse the Z axis when using the dual motor adapter and enable the filament sensor
	
    #if ENABLED(CR10S) || ENABLED(CR10S_S4) || ENABLED(CR10S_S5) || ENABLED(SOVOL_SV01) || ENABLED(SOVOL_SV03)
      #define DUAL_Z_MOTORS
    #endif

    #if ENABLED(REVERSE_Z_MOTOR)
      #undef REVERSE_Z_MOTOR
    #else
      #define REVERSE_Z_MOTOR
    #endif
  
    #if ENABLED(SOVOL_SV01) || ENABLED(SOVOL_SV03) || ENABLED(ENDER3_MAX) //Have sensors that use same logic as EZOUT Sensors
      #define EZOUT_ENABLE
    #endif
  
    #if DISABLED(EZOUT_ENABLE) 
      #define CR10S_STOCKFILAMENTSENSOR
    #endif

    #if ENABLED(CR10S)
      #define CR10
    #elif ENABLED(CR10S_S4)
      #define CR10_S4
    #elif ENABLED(CR10S_S5)
      #define CR10_S5
    #endif
    
  #endif
  
  #ifndef MOTHERBOARD
    #define MOTHERBOARD BOARD_TH3D_EZBOARD
  #endif
  
  #if ENABLED(CUSTOM_ESTEPS)
    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, CREALITY_Z_STEPS, CUSTOM_ESTEPS_VALUE }
  #elif ENABLED(SOVOL_SV01) || ENABLED(SOVOL_SV03)
    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, CREALITY_Z_STEPS, 402 }
  #else
    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, CREALITY_Z_STEPS, 95 }
  #endif
  
  #define SHOW_BOOTSCREEN
  
  #define EXTRUDERS 1
  
  #if ENABLED(CR10)
    #define X_BED_SIZE 300
    #define Y_BED_SIZE 300
    #define Z_MAX_POS 400
    #define PRINTER_VOLTAGE_12
  #endif

  #if ENABLED(CR10_MINI) || ENABLED(CR10S_MINI)
    #define X_BED_SIZE 300
    #define Y_BED_SIZE 220
    #define Z_MAX_POS 300
    #define PRINTER_VOLTAGE_12
  #endif

  #if ENABLED(CR10_S4)
    #define X_BED_SIZE 400
    #define Y_BED_SIZE 400
    #define Z_MAX_POS 400
    #define PRINTER_VOLTAGE_12
    #define SLOWER_PROBE_MOVES
  #endif

  #if ENABLED(CR10_S5)
    #define X_BED_SIZE 500
    #define Y_BED_SIZE 500
    #define Z_MAX_POS 500
    #define PRINTER_VOLTAGE_12
    #define SLOWER_PROBE_MOVES
  #endif

  #if ENABLED(ENDER2)
    #define X_BED_SIZE 160
    #define Y_BED_SIZE 150
    #define Z_MAX_POS 220
    #define PRINTER_VOLTAGE_12
  #endif

  #if ENABLED(ENDER2_PRO)
    #define X_BED_SIZE 165
    #define Y_BED_SIZE 168
    #define Z_MAX_POS 180
    #define PRINTER_VOLTAGE_24
  #endif

  #if ENABLED(ENDER3)
    #if ENABLED(XTENDER_E3_300)
      #define X_BED_SIZE 300
      #define Y_BED_SIZE 300
      #define Z_MAX_POS 250
    #elif ENABLED(XTENDER_E3_300XL)
      #define X_BED_SIZE 300
      #define Y_BED_SIZE 300
      #define Z_MAX_POS 400
    #elif ENABLED(XTENDER_E3_400)
      #define X_BED_SIZE 400
      #define Y_BED_SIZE 400
      #define Z_MAX_POS 250
    #elif ENABLED(XTENDER_E3_400Z)
      #define X_BED_SIZE 235
      #define Y_BED_SIZE 235
      #define Z_MAX_POS 400
    #elif ENABLED(XTENDER_E3_400XL)
      #define X_BED_SIZE 400
      #define Y_BED_SIZE 400
      #define Z_MAX_POS 500
    #elif ENABLED(XTENDER_E3_500Z)
      #define X_BED_SIZE 235
      #define Y_BED_SIZE 235
      #define Z_MAX_POS 500
    #else
      #define X_BED_SIZE 235
      #define Y_BED_SIZE 235
      #define Z_MAX_POS 250
    #endif
    #define PRINTER_VOLTAGE_24
  #endif

  #if ENABLED(ENDER3_MAX)
    #define X_BED_SIZE 300
    #define Y_BED_SIZE 300
    #define Z_MAX_POS 340
    #define PRINTER_VOLTAGE_24
    #define MOUNTED_FILAMENT_SENSOR
  #endif

  #if ENABLED(ENDER5)
    #if ENABLED(XTENDER_E5_5XL)
      #define X_BED_SIZE 235
      #define Y_BED_SIZE 235
      #define Z_MAX_POS 500
    #else
      #define X_BED_SIZE 220
      #define Y_BED_SIZE 220
      #define Z_MAX_POS 300
    #endif
    #define PRINTER_VOLTAGE_24
  #endif
  
  #if ENABLED(ENDER5_PLUS)
    #if ENABLED(XTENDER_E5P_400)
      #define X_BED_SIZE 510
      #define Y_BED_SIZE 510
      #define Z_MAX_POS 400
    #elif ENABLED(XTENDER_E5P_500)
      #define X_BED_SIZE 510
      #define Y_BED_SIZE 510
      #define Z_MAX_POS 500
    #else
      #define X_BED_SIZE 350
      #define Y_BED_SIZE 350
      #define Z_MAX_POS 400
    #endif
    #define PRINTER_VOLTAGE_24
    #if DISABLED(REVERSE_KNOB_DIRECTION)
      #define REVERSE_ENCODER_DIRECTION
    #endif
    #define EZOUT_ENABLE
    #define DUAL_Z_MOTORS
    #define MOUNTED_FILAMENT_SENSOR
  #endif

  #if ENABLED(SOVOL_SV01)
    #define X_BED_SIZE 280
    #define Y_BED_SIZE 240
    #define Z_MAX_POS 300
    #define PRINTER_VOLTAGE_24
  #endif
  
  #if ENABLED(SOVOL_SV03)
    #define X_BED_SIZE 350
    #define Y_BED_SIZE 350
    #define Z_MAX_POS 400
	#define PRINTER_VOLTAGE_24
  #endif

  #if ENABLED(CR20)
    #define X_BED_SIZE 220
    #define Y_BED_SIZE 220
    #define Z_MAX_POS 250
    #define PRINTER_VOLTAGE_24
  #endif
  
  #if (CUSTOM_ZHEIGHT > Z_MAX_POS)
    #undef Z_MAX_POS
    #define Z_MAX_POS CUSTOM_ZHEIGHT
  #endif

  #if ENABLED(HOME_ADJUST)
    #define X_MIN_POS X_HOME_LOCATION
    #define Y_MIN_POS Y_HOME_LOCATION
  #elif ENABLED(ENDER2_PRO_OEM)
    #define X_MIN_POS -9
    #define Y_MIN_POS -4
  #elif ENABLED(ENDER2_PRO_OEM_MICRO)
    #define X_MIN_POS -9
    #define Y_MIN_POS -4
  #elif ENABLED(ENDER2_PRO)
    #define X_MIN_POS -20
    #define Y_MIN_POS -4
  #else
    #define X_MIN_POS 0
    #define Y_MIN_POS 0
  #endif
  
  #if ENABLED(ENDER5) || ENABLED(ENDER5_PLUS)
    #define USE_XMAX_PLUG
    #define USE_YMAX_PLUG
    #define USE_ZMIN_PLUG
  #else
    #define USE_XMIN_PLUG
    #define USE_YMIN_PLUG
    #define USE_ZMIN_PLUG
  #endif
  
  #if ENABLED(ENDER5) || ENABLED(ENDER5_PLUS)
    #define X_HOME_DIR 1
    #define Y_HOME_DIR 1
    #define Z_HOME_DIR -1
  #else
    #define X_HOME_DIR -1
    #define Y_HOME_DIR -1
    #define Z_HOME_DIR -1
  #endif
  
  #if NONE(V6_HOTEND, TH3D_HOTEND_THERMISTOR, KNOWN_HOTEND_THERMISTOR, EZBOARD_PT100)
    #define TEMP_SENSOR_0 1
  #else
    #if ENABLED(EZBOARD_PT100)
      #define TEMP_SENSOR_0 20
    #elif ENABLED(V6_HOTEND)
      #define TEMP_SENSOR_0 5
    #elif ENABLED(KNOWN_HOTEND_THERMISTOR)
      #define TEMP_SENSOR_0 KNOWN_HOTEND_THERMISTOR_VALUE
    #elif ENABLED(TH3D_HOTEND_THERMISTOR)
      #define TEMP_SENSOR_0 1
    #endif
  #endif
  
  #define TEMP_SENSOR_1 0 
  #define TEMP_SENSOR_2 0
  #define TEMP_SENSOR_3 0
  #define TEMP_SENSOR_4 0
  #define TEMP_SENSOR_5 0
  #define TEMP_SENSOR_6 0
  #define TEMP_SENSOR_7 0
  
  #if NONE(TH3D_BED_THERMISTOR, KEENOVO_TEMPSENSOR, KNOWN_BED_THERMISTOR, AC_BED)
    #define TEMP_SENSOR_BED 1
  #else
    #if ENABLED(AC_BED)
      #define TEMP_SENSOR_BED 0
    #elif ENABLED(KNOWN_BED_THERMISTOR)
      #define TEMP_SENSOR_BED KNOWN_BED_THERMISTOR_VALUE
    #elif ENABLED(TH3D_BED_THERMISTOR)
      #define TEMP_SENSOR_BED 1
    #elif ENABLED(KEENOVO_TEMPSENSOR)
      #define TEMP_SENSOR_BED 11
    #endif
  #endif
    
  #define TEMP_SENSOR_PROBE 0
  #define TEMP_SENSOR_CHAMBER 0

  #if ENABLED(V3_EZABL_ON_SERVO)
    #define ENDSTOPPULLUP_ZMIN
    #define ENDSTOPPULLUP_ZMIN_PROBE
  #endif

  #define X_MIN_ENDSTOP_INVERTING false
  #define Y_MIN_ENDSTOP_INVERTING false
  #define Z_MIN_ENDSTOP_INVERTING false
  #define X_MAX_ENDSTOP_INVERTING false
  #define Y_MAX_ENDSTOP_INVERTING false
  #define Z_MAX_ENDSTOP_INVERTING false
  #define Z_MIN_PROBE_ENDSTOP_INVERTING false
  #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN

  #define X_DRIVER_TYPE  TMC2208
  #define Y_DRIVER_TYPE  TMC2208
  #define Z_DRIVER_TYPE  TMC2208
  #define E0_DRIVER_TYPE TMC2208

  #define X_ENABLE_ON 0
  #define Y_ENABLE_ON 0
  #define Z_ENABLE_ON 0
  #define E_ENABLE_ON 0

  #if ENABLED(ENDER2_PRO)
    #if ENABLED(REVERSE_X_MOTOR)
      #define INVERT_X_DIR true
    #else
      #define INVERT_X_DIR false
    #endif
  #else
    #if ENABLED(REVERSE_X_MOTOR)
      #define INVERT_X_DIR false
    #else
      #define INVERT_X_DIR true
    #endif
  #endif

  #if ENABLED(ENDER2_PRO)
    #if ENABLED(REVERSE_Y_MOTOR)
      #define INVERT_Y_DIR true
    #else
      #define INVERT_Y_DIR false
    #endif
  #else
    #if ENABLED(REVERSE_Y_MOTOR)
      #define INVERT_Y_DIR false
    #else
      #define INVERT_Y_DIR true
    #endif
  #endif

  #if ANY(ENDER5, ENDER2_PRO)
    #if ENABLED(REVERSE_Z_MOTOR)
      #define INVERT_Z_DIR false
    #else
      #define INVERT_Z_DIR true
    #endif
  #else
    #if ENABLED(REVERSE_Z_MOTOR)
      #define INVERT_Z_DIR true
    #else
      #define INVERT_Z_DIR false
    #endif
  #endif
  
  #if ANY(SOVOL_SV01, ENDER2_PRO)
    #if ENABLED(REVERSE_E_MOTOR_DIRECTION)
      #define INVERT_E0_DIR true
    #else
      #define INVERT_E0_DIR false
    #endif
  #else
    #if ENABLED(REVERSE_E_MOTOR_DIRECTION)
      #define INVERT_E0_DIR false
    #else
      #define INVERT_E0_DIR true
    #endif
  #endif

  #define INVERT_E1_DIR false
  #define INVERT_E2_DIR false
  #define INVERT_E3_DIR false
  #define INVERT_E4_DIR false
  #define INVERT_E5_DIR false

  #define ENCODER_PULSES_PER_STEP 4
  #define ENCODER_STEPS_PER_MENU_ITEM 1
  
  #if ENABLED(ENDER5_PLUS)
    #if DISABLED(ENDER5_PLUS_NOABL) && DISABLED(ENDER5_PLUS_EZABL)
      #define BLTOUCH
    #define SERVO0_PIN P2_04
    #ifndef EZABL_PROBE_EDGE
      #define EZABL_PROBE_EDGE 15
    #endif
    #ifndef EZABL_POINTS
      #define EZABL_POINTS 5
    #endif
    #if DISABLED(CUSTOM_PROBE)
        #define CUSTOM_PROBE
        #define NOZZLE_TO_PROBE_OFFSET { -44, -9, 0}
      #endif
    #endif  
    #if DISABLED(ENDER5_PLUS_NOABL)
      #define ABL_ENABLE
    #endif
  #endif
  
  #if ENABLED(SOVOL_SV03)
    #if DISABLED(SV03_NOABL) && DISABLED(SV03_EZABL)
      #if DISABLED(BLTOUCH)
        #define BLTOUCH
      #endif
      
      #ifndef SERVO0_PIN
        #define SERVO0_PIN P2_04
      #endif
      
      #if DISABLED(CUSTOM_PROBE)
        #define CUSTOM_PROBE
        #define NOZZLE_TO_PROBE_OFFSET { -34, -13, 0 }
      #endif
    #endif  
  #endif

  #define EZBOARD

  #if ENABLED(EZOUT_ENABLE) || ENABLED(CR10S_STOCKFILAMENTSENSOR)
    #define FILAMENT_RUNOUT_SENSOR
  #endif
  
  #if ENABLED(FILAMENT_RUNOUT_SENSOR)
    
    #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
    #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
    
    #if ENABLED(EZOUT_ENABLE)
      #define FIL_RUNOUT_STATE LOW  // Pin state indicating that filament is NOT present.
    #else
      #define FIL_RUNOUT_STATE HIGH // Pin state indicating that filament is NOT present.
    #endif
    
    #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
    //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.

    // Set one or more commands to execute on filament runout.
    // (After 'M412 H' Marlin will ask the host to handle the process.)
    #define FILAMENT_RUNOUT_SCRIPT "M600"

    // After a runout is detected, continue printing this length of filament
    // before executing the runout script. Useful for a sensor at the end of
    // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
    //#define FILAMENT_RUNOUT_DISTANCE_MM 25

    #ifdef FILAMENT_RUNOUT_DISTANCE_MM
      // Enable this option to use an encoder disc that toggles the runout pin
      // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
      // large enough to avoid false positives.)
      //#define FILAMENT_MOTION_SENSOR
    #endif
  #endif

  #if ENABLED(EZNEO_220)
    #define RGB_LIGHTS
    #define NEOPIXEL_LED
    #if ENABLED(NEOPIXEL_LED)
      #define NEOPIXEL_TYPE   NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
      #ifndef NEOPIXEL_PIN
        #define NEOPIXEL_PIN    P0_03    // LED driving pin
      #endif
      #define NEOPIXEL_PIXELS 15       // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
      #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
      #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness (0-255)
      #define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
    #endif

    /**
     * Printer Event LEDs
     *
     * During printing, the LEDs will reflect the printer status:
     *
     *  - Gradually change from blue to violet as the heated bed gets to target temp
     *  - Gradually change from violet to red as the hotend gets to temperature
     *  - Change to white to illuminate work surface
     *  - Change to green once print has finished
     *  - Turn off after the print has finished and the user has pushed a button
     */
    #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
      #define PRINTER_EVENT_LEDS
    #endif
  #endif
  
#endif
//End EZBoard based Machine Settings

/*
 * All other settings are stored in the Configuration_backend.h and Configuration_speed.h files. Do not change unless you know what you are doing.
 */
 
#include "Configuration_backend.h"
#include "Configuration_speed.h"